- 您现在的位置：买卖IC网 > Sheet目录311 > AS5043 PB (ams)BOARD PROGRAM AS5043
AS5043
Data Sheet - Pin Configuration
5.1 Pin Description
Pins 7, 15 and 16 are supply pins, pins 5, 13 and 14 are for internal use and must be left open.
Pin 1 is the magnetic field strength indicator, MagRNGn . It is an open-drain output that is pulled to VSS when the
magnetic field is out of the recommended range (45mT to 75mT). The chip will still continue to operate, but with reduced
performance, when the magnetic field is out of range. When this pin is low, the analog output at pins #10 and #12 will be
0V to indicate the out-of-range condition.
Pin 2 MODE allows switching between filtered (slow) and unfiltered (fast mode). This pin must be tied to VSS or VDD5V,
and must not be switched after power up. See section 0.
Pin 3 Chip Select ( CSn ; active low) selects a device for serial data transmission over the SSI interface. A “logic high” at
CSn forces output DO to digital tri-state.
Pin 4 CLK is the clock input for serial data transmission over the SSI interface (see section 1)
Pin 6 DO (Data Out) is the serial data output during data transmission over the SSI interface (see section 1)
Pin 8 PROG_DI is used to program the different operation modes, as well as the zero-position in the OTP register.
This pin is also used as a digital input to shift serial data through the device in Daisy Chain Configuration, (see page 9).
Pin 9 DACref is the external voltage reference input for the Digital-to-Analog Converter (DAC). If selected, the analog
output voltage on pin 12 (V out ) will be ratiometric to the voltage on this pin.
Pin10 DACout is the unbuffered output of the DAC. This pin may be used to connect an external OPAMP, etc. to the
DAC.
Pin 11 FB ( F eed b ack) is the inverting input of the OPAMP buffer stage.
Access to this pin allows various OPAMP configurations.
Pin 12 Vout is the analog output pin. The analog output is a DC voltage, ratiometric to VDD5V (3.0 – 5.5V) or an external
voltage source and proportional to the angle.
www.austriamicrosystems.com
Revision 1.80
3 – 36
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AS5045 PB
BOARD PROGRAM AS5045
AS5134 PB
BOARD PROGRAM AS5134
AS5140 PB
BOARD PROGRAM AS5140
ASDMB-ADAPTER-KIT
ASDMB MEMSPEED P II OSC KIT
ASFLMPLP-ADAPTER-KIT
ASFLMPLP MEMSPEED P II OSC KIT
AT24C01-10SI-1.8
IC EEPROM 1KBIT 400KHZ 8SOIC
AT24C01B-TSU-T
IC EEPROM 1KBIT 1MHZ SOT23-5
AT24C02C-XHM-B
IC EEPROM 2KBIT 1MHZ 8TSSOP
相关代理商/技术参数
AS5043_1
制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Programmable 360 Magnetic Angle Encoder with Absolute SSI and Analog Outputs
AS5043-AB
制造商:ams 功能描述:Magnetic Sensor Development Tools AS5043 Adapter Board
AS5043-ASSM
功能描述:IC ENCODER PROG 10-BIT 16-SSOP 制造商:ams 系列:- 零件状态:有效 用于测量:角度 技术:霍尔效应 旋转角 - 电气，机械:0° ~ 360°，连续 线性范围:- 输出:模拟电压 输出信号:- 致动器类型:外磁铁，不含 线性度:±0.5° 电阻（欧姆）:- 电阻容差:- 电压 - 电源:4.5 ~ 5.5V 安装类型:表面贴装 端子类型:* 工作温度:-40°C ~ 125°C 标准包装:500
AS5043ASST
制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Programmable 360 Magnetic Angle Encoder with Absolute SSI and Analog Outputs
AS5043-ASST
功能描述:IC ENCODER PROG 10-BIT 16-SSOP RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
AS5043ASSU
制造商:AMS 功能描述:IC MAGNETIC ROTARY ENCODER 10BIT SSOP16 制造商:AMS 功能描述:IC, MAGNETIC ROTARY ENCODER 10BIT SSOP16; IC Function:Encoder IC; Brief Features:360 Contactless High Resolution Angular Position Encoding, Two 10-bit Absolute Output; Supply Voltage Min:3V; Supply Voltage Max:3.6V; No. of Pins:16 ;RoHS Compliant: Yes
AS5043-ASSU
功能描述:板机接口霍耳效应/磁性传感器 RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
AS5043TR
制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:PROGRAMMABLE 360° MAGNETIC ANGLE ENCODER WITH ABSOLUTE SSI AND ANALOG OUTPUTS